Arduino LilyPad ATmega168V Development Board - Arduino Compatible

  • RM26.50

  • Ex Tax: RM25.00
  • Product Code: LilyPad
  • Availability: In Stock

The LilyPad Arduino is a microcontroller board designed for wearables and e-textiles. It can be sewn to fabric and similarly mounted power supplies, sensors and actuators with conductive thread. The board is based on the ATmega168V (the low-power version of the ATmega168). The LilyPad Arduino was designed and developed by Leah Buechley and SparkFun Electronics.


LilyPad is a wearable e-textile technology developed by Leah Buechley and cooperatively designed by Leah and SparkFun. Each LilyPad was creatively designed to have large connecting pads to allow them to be sewn into clothing. Various input, output, power, and sensor boards are available. They're even washable!

 

The LilyPad is compatible with an FTDI cable and the Arduino LilyPad/Pro/ProMini Programmer. This allows the LilyPad to work with the auto-reset feature used in the Arduino software. The LilyPad is no longer compatible with the LilyPad USB Link.

Warning: Don't power the LilyPad Arduino with more than 5.5 volts, or plug the power in backward: you'll kill it.

 

Specifications

  • Microcontroller: ATmega168V
  • Operating Voltage: 2.7-5.5 V
  • Input Voltage: 2.7-5.5 V
  • Digital I/O Pins: 14 (of which 6 provide PWM output)
  • Analog Input Pins: 6
  • DC Current per I/O Pin: 40 mA
  • Flash Memory: 16 KB (of which 2 KB used by bootloader)
  • SRAM: 1 KB
  • EEPROM: 512 bytes
  • Clock Speed: 8 MHz
  • Dimensions
    • 50mm outer diameter
    • Thin 0.8mm PCB 

 

Programming

The LilyPad Arduino can be programmed with the Arduino software (download). *Note*, the LilyPad Arduino should only be programmed with software versions 0010 or higher. You can program it with earlier versions, but all of the time related functions will be off (twice as slow as they should be).

The ATmega168V on the Arduino LilyPad comes preburned with a bootloader that allows you to upload new code to it with the Arduino software. The bootloader on the most recent LilyPad boards is Limor Fried's "no wait" bootloader. When the LilyPad is supplied with power, its Arduino sketch starts immediately. The bootloader is triggered only when the reset switch is pressed. You can also bypass the bootloader and program the ATmega168V through the ICSP (In-Circuit Serial Programming) header; see these instructions for details.

 

Power

The LilyPad Arduino can be powered via the USB connection or with an external power supply.

If an external power supply is used, it should provide between 2.7 and 5.5 volts. This can come either from an AC-to-DC adapter (wall-wart) or battery. Again, don't power the LilyPad Arduino with more than 5.5 volts, or plug the power in backwards: you'll kill it.

 

Physical Characteristics

The LilyPad Arduino is a circle, approximately 50mm (2") in diameter. The board itself is .8mm (1/32") thick (approximately 3mm (1/8") where electronics are attached).

 

Washability

Wash at your own risk - we do ;). We recommend washing projects by hand with a mild detergent. Drip dry. Make sure you remove your power supply first! 

 

 

Suggestions

Arduino LilyPad Programmer:

 

FTDI USB to TTL Serial UART Converter Module FT232RL

Programmer for Arduino Pro, Pro Mini, LilyPad

Jumper Wire 10-pin Female~Female 10cm for Breadboard

LilyPad Power Supply AAA

LilyPad Tri-Color LED RGB Module

Lilypad Conductive Sewing Thread

 

Write a review

Note: HTML is not translated!
    Bad           Good

Similar Products